提高印刷品光泽度的方法 - 常见问题

济南丰印纸制品有限公司为您提供济南uedbet官网进不去济南uedbet彩票uedbet官网进不去济南uedbet官网进不去包装等相关信息发布和相关资讯,敬请关注!

联系我们
热线电话:
13465900292
联系人:鞠经理
手机:15589938556
邮箱: 50062082@qq.com
网址:http://www.xinfengyinshua.cn/
地址:山东省济南市明湖西路777号明湖广场1号楼1-810

提高uedbet官网进不去品光泽度的方法

来源:http://www.xinfengyinshua.cn/   发布时间:2021-07-26
光泽,作为视觉信息的一种,能对人的心理状态、情绪等许多精神方面产生重要影响,所以人们对于颜色的研究很早就开始了,对于uedbet官网进不去行业来说,一件uedbet官网进不去成品有无光泽是尤为重要的。那么在不考虑印后上光处理的前提下,应如何有用提高uedbet官网进不去品的光泽度呢?下面,我们就来了解一下。
Gloss, as a kind of visual information, can have an important impact on people's mental state, emotion and many other spiritual aspects. Therefore, people's research on color has begun very early. For the printing industry, whether a printed product has gloss is particularly important. So how to effectively improve the gloss of printed matter without considering the post press polishing treatment? Now, let's take a look.
1、改进酸性润湿液。
1. Improve acid wetting solution.
以铬酸、磷酸为主,酸性越强,对油墨连结料和颜料的分解力、腐蚀力越大,致使印迹膜面粗糙,降低了光泽。
It is mainly chromic acid and phosphoric acid. The stronger the acidity, the greater the decomposition and corrosion of ink binder and pigment, resulting in rough surface of imprinted film and reduced gloss.
2、降低油墨乳化度。
2. Reduce ink emulsification.
胶印中的油墨乳化过度大都是操作中水大墨多造成的,印迹看上去墨层很厚,但油墨分子成了水包油的状态,干燥后光泽性非常差,而且还会产生一系列其它故障。水大墨多是胶印中比较犯忌的做法。
The excessive emulsification of ink in offset printing is mostly caused by large amount of water and ink in operation. The ink layer looks very thick, but the ink molecules become oil in water. After drying, the gloss is very poor, and a series of other faults will occur. Water and ink are mostly taboo practices in offset printing.
3、油墨中适当的加放辅助剂。
3. Add appropriate auxiliary agent in the ink.
在油墨中加放适当的辅助剂,可以调节油墨的uedbet官网进不去适性,以便顺利uedbet官网进不去,绝大部分辅助剂对于成品光泽都会带来不利影响。例如防粘剂,主要原料为六谷粉,加入油墨后,印迹膜层表面由于玉米粉的析出而变的粗糙,成品光泽性就差。
Adding appropriate auxiliary agents to the ink can adjust the printability of the ink for smooth printing. Most auxiliary agents will have an adverse impact on the gloss of the finished product. For example, the main raw material of the anti adhesion agent is Liugu powder. After adding ink, the surface of the imprinted film becomes rough due to the precipitation of corn flour, and the gloss of the finished product is poor.
4、正确使用燥油。
4. Use dry oil correctly.
对于高级的亮光快干油墨,在温、湿度正常的情况下,自身已有足够的干燥能力。如果在冬季温、湿度偏低或者油墨内须添加防粘剂、去粘剂、薄调墨油等的情况下,都应加放燥油。在工艺操作中,正确的使用燥油,对于成品形成光泽非常有利。这是因为纸张吸收连结料需要一定的时间,在此过程中,尽快使连结料凝聚,直至结膜干燥,是成品光泽好的关键。
For advanced bright quick drying ink, it has sufficient drying capacity under normal temperature and humidity. If the temperature and humidity are low in winter or the ink must be added with anti adhesion agent, de adhesion agent, thin ink blending oil, etc., the drying oil shall be added. In the process operation, the correct use of dry oil is very beneficial to the formation of luster of the finished product. This is because it takes some time for the paper to absorb the binder. In this process, it is the key to make the binder agglomerate as soon as possible until the conjunctiva is dry.
5、注意喷粉。
5. Pay attention to powder spraying.
喷粉同油墨一样,也会产生凝聚,特别是密封不好的袋装或桶装,喷粉受潮后,凝聚成较大的颗粒,喷到湿墨印迹上,使墨层表面结膜粗糙,降低了原有的光泽,因此喷粉要注意防潮。另外,喷粉装置的机构上有加热装置,在使用喷粉时应加以检查,加热装置是否失灵。
Like ink, powder spraying will also produce condensation, especially in bags or barrels with poor sealing. After powder spraying is damp, it will condense into larger particles and spray them on the wet ink imprint, making the conjunctiva on the surface of the ink layer rough and reducing the original luster. Therefore, powder spraying should pay attention to moisture-proof. In addition, there is a heating device on the mechanism of the powder spraying device. When using the powder spraying device, check whether the heating device fails.
除此之外,正确调节机器,也可以提高uedbet官网进不去品光泽度,印迹墨层厚度是否达到标准,对于光泽也有影响,因此,要把压力调整好,使网点的扩大率控制在15%左右,所印的产品墨层既厚实,层次又拉的开,光泽自然也会有了。
In addition, the correct adjustment of the machine can also improve the gloss of printed products. Whether the thickness of the imprinted ink layer meets the standard also has an impact on the gloss. Therefore, the pressure should be adjusted well to control the dot expansion rate at about 15%. The ink layer of the printed products is thick and open, and the gloss will naturally be improved.
济南uedbet官网进不去厂讲解的内容  更多的内容  请咨询公司官网http://www.xinfengyinshua.cn/